澳门新葡亰赌995577_www.995577.com

欢迎访问澳门新葡亰赌995577官网!

伺服系统

联系我们

澳门新葡亰赌995577

联系人:王小姐

深圳总公司电话:0755-36560048

东莞分公司电话: 0769-28633757

企业400电话:4000887900

手机:15814107663

邮箱:wangluotuiguang@yixincnc.com

传真:0755-23068836

地址:深圳市宝安区福永街道福洲大道24号中阳商务大厦4楼408

东莞分公司地址:东莞市南城区白马永利达科技园A栋3楼

网址:www.yixincnc.com

中大高精度行星减速机

您的当前位置: 首 页 >> 产品中心 >> 中大减速机

中大高精度行星减速机

  • 详细介绍

1、中大ZE系列减速机剖视图:

减速机

①输出轴0 utput shaft

②油封 Oil seal

③输出轴前轴承0 utput shaft front bearing

④行星轮 Planetary gear

⑤太阳轮 Solar wh

⑥满针轴承 Full needle bearing

⑦前盖 Front cover

⑧输出轴后轴承 Output shaft rear bearing

⑨油封 Oil seal

⑩联轴器 Coupling

?锁紧环 Lock ring

?后盖 rear cover






减速机


①减速机机座号:090 具体见P08

②减速机系列代号ZE

③减速比:20具体见P08

④.精度具体见P08 

标准型P2(省略)精密型P1高精密型P0

输出轴负荷量为容许输出扭矩的±5%时的值 

⑤输入轴型式 

S:整体锁紧省略)无论马达是否有键槽都可使用,但℃字型不适用

S1:带锁紧环锁紧(无论马达是否有键槽都可使用,但"字型不适用 

S2带键槽锁紧输入轴带键)

κ:带键槽

A其他适配器请与本公司联系)

⑥适用伺服马达功率W

⑦伺服马达厂家名称P11-P12

⑧伺服马达型号

①Gear head frame size: 090

②Gear head series code ZE

③Gear Ratio: Single Stage 20, (P08

④Amount of backlash, ( P08

Standard type P2 precision P1 high precision PO

precision ( the load of output shaft is+5% of allowable output torque) 

⑤Input shaft type

S: Over locking(OmissionMregardless whether the motor with key way can use it But D Cut can' t use) S1: Locking with locking ring(regardless whether the motor with keyway can use it But D Cut cant use)

S2: Locking with keyway (input shaft with key) 

K:With keyway 

A: Other type(please contact with us)

⑥Applicable servo motor power (W)

⑦Manufacturer name of servo motor(P11-P12)

⑧Model of servo mot

减速机


减速机

减速机

减速机

注1)没有油封和尺寸不同时,安装带油封的马达有时需特别订货

if an oil-seal is not present and the size is different, attachment of the oil-seal may correspond to special order, in some cases 

注2)马达轴为D形轴、锥形时需要特别订货。 the motor shaft is of D-cut and taper type, it corresponds to a special order.

注3)因马达功率(适用表中带※的马达)与减速比的组合,岀现瞬间最大输岀扭矩时,产生的轴向力有时会超过伺服马达容许轴向力,因此,需要注意。

Note that thrust power arsing out of instantaneous max, output torque bu the combination of motor capactith (motor of the motor series table) and reduction ratio may exceed 

permissible thrust power of the servo motor.

注4)标准外有时需要特别订货。欲知详情,请另外与本公司联系

Out-of-standard may correspond to a special order in some cases, For details, contact us

减速机

注1)没有油封和尺寸不同时,安装带油封的马达有时需特别订货。

注2)马达轴为υ形轴、锥形时需要特别订货。

注3)因马达功率(适用表中带※的马达)与减速比的组合,出现瞬间最大输出扭矩时,产生的轴向力有时会超过伺服马达容许轴向力,因此,需要注意。注4)标准外有时需要特别订货。欲知详情,请另外与本公司联系。

 

Note1)If an oil-seal is not present and the size is different, attachment of the oil-seal may correspond to specia order, in some cases. Note2) If the motor shaft is of D-cut and taper type, it corresponds to a special order. Note3) Note that thrust power arsing out of instantaneous max, ouyput torque bu the combination of motor capactith(motor of the motor eries table)and reduction ratio may exceed permissible thrust power of the servo motor. Note 4)Out-of-standard may correspond to a special order in some cases, For details,


除上述伺服马达厂家外,本公司减速机还适配以下伺服马达厂家。安装方式请咨询本公司

Our gearbox can match to servo motor of followings manufacturers, including aboves. Please ask us about the assembly

减速机

■安装马达的步骤 Assembly Procedure

客户自行安装伺服马达时,请按以下要领进行安装。伺服马达的尺寸多种多样,除指定的产品外,有些马达可能会无法连接法兰,因为,一定要使用您订货时指定的马达

personally bles the servo motor and reducer please use the following tip. The reducer flange to which the servo motor is attached has different dimensions based specified. Therefore, assembly may be impossible for some motor. Make sure the correct motor is specified before ordering the reducer.

减速机安装无键马达 Spec In Case 0f Assembling A Motor Without Key

①拧去紧定螺钉,转动输入轴,使螺栓头和紧定螺钉的孔吻合。并确认固定螺栓已松开。

Take off the rubber cap, turn the input shaft, and match the head of the bolt to the hole of the rubber cap. Make sure that the set bolt is loosened

②将马达轴平稳地插入翰岀轴(请确保不受阻塞地顺畅的插入)。请充分注意不要让马达倾斜插入。

Gradually put the motor shaft into the input shaft (Ensure that it is smoothly put in without iam.) 

e careful not to be inserted with the motor tilted

③将马达固定在减速机上,并按指定的扭矩将螺栓拧紧。参考表1

Attach the motor to the reducer and fasten the bolt with designated fastening torque. See Table 1

④使用扭矩扳手等工具,按指定的扭矩将输入轴的固定嫘栓拧紧。参考表

Fasten the set bolt of the input shaft with designated fastening torque wrench, etc. See Table 2 

⑤拧上紧定螺钉。安装到此结束

Puton a rubber cap. It is the end of assembling


减速机

减速机


本文网址:/product/738.html

关键词:东莞行星减速机,精密行星减速机供应商,行星减速机价格

上一篇:没有了
下一篇:没有了

最近浏览:

  • 在线客服
    在线客服在线客服
  • 联系电话
    15814107663
  • 在线留言
  • 关注公众号
  • 在线咨询
    XML 地图 | Sitemap 地图